Answer
This E11 error indicates that the washer did not fill with water quickly enough, and that it took more than 6 minutes to fill with water, which might be caused by the water not being switched on in the first place. The good news is that resolving this problem is straightforward.
What does the e11 code on an Electrolux washing machine signify in this context?
E11: The time spent filling out the form is excessive. In this case, the water tap is closed, the water flow rate is too low, the pressure sensor is faulty, the inlet valve is defective, and the air tube is kinked.
One can also wonder what the letters EHO on a washing machine stand for.
a source of electricity
In light of this, what does the code e11 on a washing machine mean?
In the case of a Hoover washing machine, an E11 error code indicates that there is a problem with the drying sensor. If the drying sensor in your washer dryer is broken or malfunctioning, you will find yourself with a washer dryer that will not dry your garments after they have been laundered.
In order to diagnose an Electrolux washing machine, you must first turn it on.
Instructions on how to access the diagnostic/service mode on an Electrolux front-loading washing machine. * Press the Cancel button to put the computer into standby mode and make it available for diagnostics. * Press any button on the remote within 10 seconds after pushing the Cancel button to bring it back to life. To enter the diagnostic mode, press and hold the button beneath the display for three seconds at a time.
There were 28 related questions and answers found.
What does the code e10 on a washing machine mean?
Problem: The washing machine shows the diagnostic codes E10 and C1 or produces one beep and one flash. It indicates an issue with the water intake, such as not taking in enough water or difficulties with the drainage system.
What is the procedure for unlocking my Electrolux washing machine?
To unlock the control, simultaneously press the “Options” and “Select” buttons on the remote. The control lock status light will no longer be illuminated, and you will be able to let your hair to regrow!
What does the letter e stand for on an Electrolux washer?
Water level does not reduce to the reset point within 15 minutes after emptying the water from the washer, resulting in an Electrolux E – Drain pump error –
What is the best way to reset my Hoover washing machine?
To restart the washer, press the power button on the control panel. Otherwise, if the machine has a “Cancel” button, press it to clear the error and then press the “Pause” or “Stop” button to return the machine to its default settings.
Exactly what does the code e03 on a Hoover washing machine mean?
Your Hoover washing machine is displaying the E03 error number, which indicates that the drum is not draining properly. This is usually caused by a blockage, which may be easily resolved in a few minutes. This video demonstrates how to empty the machine, remove the filter, and clear the error code.
What does the e13 code on my Electrolux washer mean?
The E13 error code is shown on an Electrolux washer. E13: There is a leak of water. The total time required to fill the water tank surpassed the permitted time (the sum of all the water fills between one drain phase and the next, to avoid exceeding the maximum volume) The following tests will be carried out: 1.
How long can you leave a washing machine running on pause?
You have the option of pausing the cycle. Once the cycle has been stopped, it will take 30+/- seconds for the lock mechanism to be released.
What does the code e40 on a washing machine mean?
It is possible that the door lock is malfunctioning if you see the error message E40 or if the washing machine beeps or blinks four times. It is possible that the door has not been closed correctly.
What is the best way to clean an AEG front loader?
Cleaning the detergent dispenser consists of the following steps: Wash each compartment thoroughly under hot running tap water to remove any spills or residue that has accumulated. Remove the dispenser and clean each part with an appropriate brush (such as an old toothbrush) to remove any dirt and dried soap powder/liquid that has accumulated within.
What is the best way to reset my AEG washing machine?
Guide to resetting your computer: To do this, press the two buttons at the top of the screen (soak and pre-wash). At the same time, rotate the cycle selector counter-clockwise until the gentle spin cycle is selected. When you are finished, remove the two buttons and spin the selector counter-clockwise all the way around to the off position (almost one full turn). Make an effort to wash in a regular manner.
What exactly does the code e10 on my AEG washing machine mean?
Problem: The washer dryer shows the trouble codes E10 and C1 or produces one beep and one flash. It indicates an issue with the water intake, such as not taking in enough water or difficulties with the drainage system.
What does the code e10 on my Zanussi washing machine mean?
In a Zanussi washing machine, the error code is EThe error code definition is that the washer is not correctly filled with water.
What exactly does the EHO symbol on a Zanussi washing machine mean?
There is a problem with the power supply if the washing machine shows the error message EHO / EH0 when it is turned on.
Post Views: 24Spread the love
ncG1vNJzZmivp6x7r6%2FEq6upp5mjwW%2BvzqZma2hiZ3xxfY6wn5qsXZm8pr%2BMnmhqZZ2arq95zqdknqSVmMGzu8uur2avkai1pr6NoaumpA%3D%3D